Here we have explained How to Make a Wi-Fi Antenna For Laptop 2024?
It’s not unheard of for your wifi card’s antenna to go missing. At the time of writing this post, many people were in the process of losing theirs.
There are, however, methods to create your own DIY antenna directly from the items you already have in your home. Then, how do you build a wifi antenna for your laptop?
- Utilizing an old-fashioned paper clip antenna in place of your original
- Making a directional antenna out of a Coke can.
Here are two of the finest methods to build a WiFi antenna for a laptop, with step-by-step instructions.
Two Different Ways On How to Make a Wi-Fi Antenna For Laptop?
If you want to create a wifi antenna for your laptop, here are the best two approaches that you may follow to do it.
Method 1: Antenna Made with Paper Clips
Paper clips are made entirely of metal. Therefore, you may use it to capture WiFi signals from your router to your wifi card. These items are essential.
- A ballpoint pen
- 2-inch paper clip
- Lighter
- Scissors
- Black tape – the one used to secure electronic components
- Ruler
- Wire cutters
The steps are as follows:
Step 1: Using a paperclip, carefully straighten it. Until the following stage, do not bend it over.
Step 2: The length of a typical antenna is 60 to 61 mm. Make sure the paperclip is measured and cut exactly at 61 millimeters.
Step 3: Measure 19 mm with the ruler once again. The insertion point into the port is made by bending the wire 90 degrees at that location.
Step 4: To remove the cartridge, unscrew the end of the pen. If you must use a previously used pen, be certain it is empty before you begin.
Step 5: Snap at least 18 mm from the cartridge with the assistance of the wire cutter and use it as a cover for the new antenna.
Step 6: The 18 mm cartridge should be used to cover the antenna’s bent portion. There must be at least a millimeter difference between this and the bent-over section.
Step 7: To shrink the cartridge, use a lighter in conjunction with the paperclip. You may do so by placing the lighter just underneath the cartridge.
Step 8: To keep it safe from the outside world, cover the whole structure with tape. This will stop any and all interruptions from occurring.
Step 9: In order to use your computer’s wifi, you must first attach the paper clip antenna to it. As little space as possible should be left between the paper clip and the connection pin while connecting them.
Make a wifi antenna for your PC using this guide. However, desktops are the most likely candidates for this, since they must be plugged directly into the wifi card or connection.
An external WiFi dongle would be required to do this on your laptop. Creating a paper clip antenna makes no sense while you’re doing that. In the event that the relationship does not work out in the future.
Method 2: Using a Soda Bottle
Soda can antennas are also a good option for external devices since they are directional. There are several delicate parts to your laptop. Opening it up and tinkering with its inner workings in this way can only make matters worse.
So, unless you’re having issues with your laptop or desktop’s external dongle, I wouldn’t suggest using any of these ways. Because your dongle is broken, here’s how you can get things rolling using a drink can.
The steps are as follows:
Step 1: If the Coke can isn’t completely empty, remove all of its contents.
Step 2: A cutter can be used to cut away the top of the can. You don’t want to end up in the hospital at this stage, so be cautious while using the cutter. Use scissors to remove any residual pieces after scoring around the top. It’s important that you make the cuts as cleanly as possible.
Step 3: Rinse and dry the soda can with the assistance of a basic dishwashing detergent before storing it in an airtight container.
Step 4: Make a hole approximately 4 inches from the closed end of the can with the use of a knife or a nail that has been hammered into the tip. Please be cautious not to use too much force, since this might cause the can to be damaged in the process.
Step 5: Close the can’s opening with tape. Take a coaxial cable or wire and use a wire cutter to cut both ends of the cable or wire.
Step 6: The other end of the wire is inserted into the hole you drilled in the can of soda. Tape it down to keep it safe.
Step 7: To remove the outer insulation, use wire strippers and cut it off 2 inches from the other end. Afterward, you’ll notice a transparent or clear sheath. Don’t get rid of it entirely. Instead, use a wire stripper to remove roughly an inch of the covering to see the wires within.
Step 8: The adapter’s wifi connector accepts the bare wires (external). The outside cover should be soldered so that any exposed wire is covered. In addition, you should wrap the tape around this area to protect it from the outside environment.
Step 9: Connect your laptop’s wifi adapter to the one you just linked to the can. Using the adaptor, you may connect your laptop to your wi-fi network through the can of soda.
Quick Links:
- 5 Best Laptops Under $700: [Value for Money Models]
- 10+ Best Laptops For DJs: Laptop For Music Production
- 10 Best Laptops Under $400: Updated List
- 10 Best Laptops for Game Development
- 10 Best Laptops for Watching Movies: [High-End Laptop]
Conclusion: How to Make a Wi-Fi Antenna for Laptop?
Making a wifi antenna for a laptop is difficult if you have to remove or replace any of the laptop’s internal components. As a result, you may inadvertently damage other components in the proximity of those parts if you interfere with them.
As a result, an external wifi adaptor is recommended. But if you want to enhance the adapter’s power, use the two approaches I’ve outlined in the previous paragraph.
They will aid with the transmission of all wifi signals to your laptop, hence eliminating any errant spikes and jitters that may arise. Thank you for reading.
